Author Topic: Rear Control Arms  (Read 1975 times)

0 Members and 1 Guest are viewing this topic.

Offline Norm340

  • Bone Stock
  • **
  • Posts: 34
  • PSI: 1
  • Boost n00b
    • View Profile
Rear Control Arms
« on: September 14 2020, 07:50:31 PM »
Hey Guys

If I was going to remove the lower control arm to replace the bushings.
Is there a certain way to remove the lower arms?
Like having jack stands under the frame and the floor jack under the diff then loosen the bolts.
Maybe only remove one arm at a time, is there tension on the sway bar?
That kind of stuff.

Kinda know how to remove and install the bushings but the arms not so much.

Thanks

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5549
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Re: Rear Control Arms
« Reply #1 on: September 14 2020, 09:08:47 PM »
Get the longest pry bar you can find.
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline earlbrown

  • Turbo Street Eliminator
  • ******
  • Posts: 1571
  • PSI: 6
    • View Profile
Re: Rear Control Arms
« Reply #2 on: September 15 2020, 12:43:35 AM »
The sway bar has to come off to get the arms out.  Take those bolts out, stands under the frame, then remove the control arm bolts.

  They'll be 'stuck' due to the frame being pinched in.  Just pry them out.   Without weight on the axle, nothing is going to go flying.
'87 GN - 4.2L SFI Turbocharged innercooled V6 - Chrome valve covers - supra pump - 14" K&N - 52mm throttlebody - rocker shaft supports -  1/2 intake spacer - TB coolant bypass - 3" ATR exhaust tip - Alum intake pipe - NOS timing cover - chip - relocated charcoal canister - CR42's - stock

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5549
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Re: Rear Control Arms
« Reply #3 on: September 15 2020, 09:40:35 AM »
Norm...piss on the stockers. UMI has cheap replacements.. .and they won't flex.
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9882
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Rear Control Arms
« Reply #4 on: September 15 2020, 12:16:31 PM »
I always did one side at a time just to make sure I did not have wrestle with the axle housing to get it back into place if it decided to move any.  This is one of the easier jobs to do.
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline Norm340

  • Bone Stock
  • **
  • Posts: 34
  • PSI: 1
  • Boost n00b
    • View Profile
Re: Rear Control Arms
« Reply #5 on: September 15 2020, 12:32:52 PM »
Thanks you guys.

Earl: I'll follow those instructions.

Brad: I have a squeak coming from one of those bushings and
have 4 new ones just sitting in the tool box so I thought lets have a look.
UMI says due to high demand it may take 4-5 weeks so I might check them out again just before spring.

 :atbeer: :atbeer:

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5549
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Re: Rear Control Arms
« Reply #6 on: September 15 2020, 05:27:31 PM »
Steve is correct...one side at a time. You'll need a bar to get them back into place.
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

 

SimplePortal 2.3.7 © 2008-2024, SimplePortal