« previous next »
Pages: [1] 2   Go Down

Author Topic: should I be concerned  (Read 7760 times)

0 Members and 2 Guests are viewing this topic.

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
should I be concerned
« on: January 14 2015, 08:59:00 PM »
This cam has about 5000 miles on it, there appears to be a pit in the metal a couple thou deep. it looks like it skipped over something there are breaks in the wear pattern.
The roller on the lifter looks goods.
« Last Edit: January 14 2015, 10:38:33 PM by larrym »
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
Re: should I be concerned
« Reply #1 on: January 15 2015, 12:37:20 PM »
I dropped it at the Machinist he was of the opinion run it, he is going to check it for straightness and polish all the journals and lobes.
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline motorhead

  • Turbo Street Outlaw
  • *******
  • Posts: 2267
  • PSI: 4
  • look at my balls... look at them!!!
    • View Profile
Re: should I be concerned
« Reply #2 on: January 15 2015, 01:23:23 PM »
It looks like one of Comp's low quality cores... and if so it isn't surprising that this damaged occured as the case-hardening doesn't go too deep on those.
Logged
>>>Das Instagram<<<
'80 LeMans Wagon|'87 Monte Carlo SS|'92 Camaro Z28|'07 TrailBlazer SS|'15 Colorado Z71|'19 Hellcat Widebooty M6

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
Re: should I be concerned
« Reply #3 on: January 15 2015, 01:28:20 PM »
who else makes an off the shelf roller cam for our cars?
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline motorhead

  • Turbo Street Outlaw
  • *******
  • Posts: 2267
  • PSI: 4
  • look at my balls... look at them!!!
    • View Profile
Re: should I be concerned
« Reply #4 on: January 15 2015, 01:40:35 PM »
Not sure.  I do know that I would go to Cam Motion for any roller cam these days, although a Buick V6 grind would be custom from them.  Shelf grinds are very dangerous for the reason shown above.
Logged
>>>Das Instagram<<<
'80 LeMans Wagon|'87 Monte Carlo SS|'92 Camaro Z28|'07 TrailBlazer SS|'15 Colorado Z71|'19 Hellcat Widebooty M6

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
Re: should I be concerned
« Reply #5 on: January 15 2015, 01:45:41 PM »
that's what I figured...
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline good2win22

  • Turbo Street Outlaw
  • *******
  • Posts: 2019
  • PSI: 0
  • No man lives happily lest he remove the boredom
    • View Profile
Re: should I be concerned
« Reply #6 on: January 15 2015, 01:48:17 PM »
Not sure who makes them but fullthrottle sells roller cams.  The one that has peaked my interest is the 210/215
Logged
Jason

1966 Ford Ranch Wagon
1982 Jeep Wagoneer Limited
1986 Grand National BLK PHNX
1987 Turbo Regal Limited
2018 Ram 2500 Cummins

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9957
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: should I be concerned
« Reply #7 on: January 15 2015, 02:33:45 PM »
I agree with the machinist
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline GavinHunyady

  • Turbo Street Limited
  • ***
  • Posts: 168
  • PSI: 1
  • Boost n00b
    • View Profile
Re: should I be concerned
« Reply #8 on: January 15 2015, 05:14:57 PM »
Quote from: good2win22 on January 15 2015, 01:48:17 PM
Not sure who makes them but fullthrottle sells roller cams.  The one that has peaked my interest is the 210/215
comp
Logged

Offline motorhead

  • Turbo Street Outlaw
  • *******
  • Posts: 2267
  • PSI: 4
  • look at my balls... look at them!!!
    • View Profile
Re: should I be concerned
« Reply #9 on: January 15 2015, 05:45:54 PM »
This should help explain the differences in quality available in aftermarket roller cams: http://ls1tech.com/forums/generation-iii-internal-engine/1759417-new-cam-core-comp.html
Logged
>>>Das Instagram<<<
'80 LeMans Wagon|'87 Monte Carlo SS|'92 Camaro Z28|'07 TrailBlazer SS|'15 Colorado Z71|'19 Hellcat Widebooty M6

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5630
  • PSI: 3
  • RED-RETIRED EXTREMELY DANGEROUS
    • View Profile
Re: should I be concerned
« Reply #10 on: January 15 2015, 10:16:25 PM »
Polish it and call it a day.
Logged
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline Pyro6

  • Turbo Street Eliminator
  • ******
  • Posts: 1327
  • PSI: 2
    • View Profile
Re: should I be concerned
« Reply #11 on: January 16 2015, 06:03:18 PM »
I agree with everybody else, but, what oil and filter are you using?
Logged

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
should I be concerned
« Reply #12 on: January 16 2015, 06:18:45 PM »
Wix filter and GTX with a bottle of Lucas.
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
Re: should I be concerned
« Reply #13 on: January 16 2015, 07:59:22 PM »
20 bucks and it looks brand new!
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5630
  • PSI: 3
  • RED-RETIRED EXTREMELY DANGEROUS
    • View Profile
Re: should I be concerned
« Reply #14 on: January 17 2015, 04:36:28 PM »
Larry...let me know what lifters you go with...and how you like them. I have all the parts together to build my 'retirement' engine...but I'm on the fence with which brand of lifter to go with.
Logged
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon
Pages: [1] 2   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2025, SimplePortal