Author Topic: Is Earl still making front covers?  (Read 324 times)

0 Members and 1 Guest are viewing this topic.

Offline Top Speed

  • Don't Tread on Me
  • Turbo Street Outlaw
  • *******
  • Posts: 2531
  • PSI: -2
    • View Profile
Re: Is Earl still making front covers?
« Reply #15 on: May 13 2020, 01:21:01 PM »
That's a good link to have!  I already see some stuff I need.
Champion Irons w/T&D roller rockers, TA-61 turbo, 206/206 Comp Cam,  57 lb/hr Siemens Injectors, 3000 stall PTC, PTE Plenum w/RJC Power Plate, 70 mm Accufab Throttle Body, RJC 325 Megacooler, TurboTweak 5.7/ Alky Control w/M1 methanol, 23 psig on the street, Puddn' Power engine, Borla Exhaust

Chris

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 4279
  • PSI: 3
  • HIGH SHERIFF OF HELL
    • View Profile
Re: Is Earl still making front covers?
« Reply #16 on: May 13 2020, 01:27:32 PM »
Those bolt kits are pure sex.
109 235 Cubic Inch Stock Stroke Balanced Rotating Assembly
Stock Crank
TRW .030 Pistons
Stock Rods
Stock Timing Chain/Gears
212/212 Flat Tappet Cam
JB Racing Heads
Stock Rockers
5.7 TT Race Chip
Built 2004R
AC 16930
6262 JB

6.72 at 104.67-25 PSI

I see slow people

Offline daveismissing

  • Two Buicks- too little money$$
  • Turbo Street Outlaw
  • *******
  • Posts: 6372
  • PSI: 3
  • Two Buicks- too little money$$
    • View Profile
Re: Is Earl still making front covers?
« Reply #17 on: May 13 2020, 06:05:01 PM »
Quote from: Top Speed
That's a good link to have!  I already see some stuff I need.
Hey Earl, commission? . Nah, Earls been very fair with me, be surprise at any complaints.
-Drain plug by Earl Brown, custom oil pan by Rich's Auto

Offline ss/gn

  • Bone Stock
  • **
  • Posts: 77
  • PSI: 1
    • View Profile
Re: Is Earl still making front covers?
« Reply #18 on: May 14 2020, 06:35:04 AM »
With everything else you have done a T/A cover would be a good idea. Better than a stocker or even a modded stocker. 
It's just a six cylinder, you can't loose
Kevin

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 8528
  • PSI: 29
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Is Earl still making front covers?
« Reply #19 on: May 14 2020, 09:13:31 AM »
I would not bet it being better than a modified stocker :D

Last one I saw used a HV gear set and no one can convince me that a HV gear set is not at best a kluge for a improperly built engine or at worst, a band-aid that is not only trying to cover up for an oiling deficiency but is also putting unneeded wear on the front cam bearing and unneeded strain on the cam sensor drive  which never comes to a good end.
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline phil_long

  • F47
  • Turbo Street Eliminator
  • ******
  • Posts: 1379
  • PSI: 0
  • ...far from avg
    • View Profile
Re: Is Earl still making front covers?
« Reply #20 on: May 14 2020, 05:27:06 PM »
I still have yet to check out the T/A cover. Brb. Lol

Offline daveismissing

  • Two Buicks- too little money$$
  • Turbo Street Outlaw
  • *******
  • Posts: 6372
  • PSI: 3
  • Two Buicks- too little money$$
    • View Profile
Re: Is Earl still making front covers?
« Reply #21 on: May 15 2020, 06:15:16 PM »
I just have the Melling plate with my TA cover?
-Drain plug by Earl Brown, custom oil pan by Rich's Auto