Author Topic: cold air intake  (Read 18914 times)

0 Members and 1 Guest are viewing this topic.

Offline Shimy87

  • Turbo Street Eliminator
  • ******
  • Posts: 1244
  • PSI: 2
    • View Profile
cold air intake
« on: July 28 2014, 10:36:28 AM »
Made this over weekend. 3 inch exhaust pipe, sheetmetal shroud/box with 1/4 in slit hose around edges. Cut out area where stock filter housing was mounted to open to air under nose of car. Probably wont really do anything but it was a rainy day
87 GN, K&N cold air, gutted cat, TT 5.7 chip, AFPR, 340 Walbro w/ hotwire, 60 LBS injectors, 981 valve springs, 206/206 Cam, RJC Powerplate, LS1 MAF & translator, Vacuum brakes, Hellwig rear sway bar, Energy suspension poly bushings, Razors Alky, Pypes exhaust, 5931 turbo, CK9.5 converter

Offline earlbrown

  • Moderator
  • Turbo Street Eliminator
  • ******
  • Posts: 1571
  • PSI: 6
    • View Profile
Re: cold air intake
« Reply #1 on: July 28 2014, 01:59:32 PM »
Without a lid it probably don't do much....

But the IAT reading will tell you if the air temp is lowered.
'87 GN - 4.2L SFI Turbocharged innercooled V6 - Chrome valve covers - supra pump - 14" K&N - 52mm throttlebody - rocker shaft supports -  1/2 intake spacer - TB coolant bypass - 3" ATR exhaust tip - Alum intake pipe - NOS timing cover - chip - relocated charcoal canister - CR42's - stock

Offline instro84

  • Bone Stock
  • **
  • Posts: 22
  • PSI: 0
    • View Profile
Re: cold air intake
« Reply #2 on: August 06 2014, 12:17:22 AM »
nice looking project.

Offline puzzledfox

  • Newbie
  • *
  • Posts: 7
  • PSI: 0
  • Boost n00b
    • View Profile
Re: cold air intake
« Reply #3 on: February 19 2017, 06:07:30 PM »
Did installing a cold air intake improve your ride's  fuel efficiency and horsepower?

Offline earlbrown

  • Moderator
  • Turbo Street Eliminator
  • ******
  • Posts: 1571
  • PSI: 6
    • View Profile
Re: cold air intake
« Reply #4 on: February 20 2017, 01:25:46 AM »
Mileage will drop as the temps go lower.

Without some probes it's hard to tell if pressure in that box was higher or lower than normal.


If higher it probably won't make measurable power until you hit about 250MPH.
'87 GN - 4.2L SFI Turbocharged innercooled V6 - Chrome valve covers - supra pump - 14" K&N - 52mm throttlebody - rocker shaft supports -  1/2 intake spacer - TB coolant bypass - 3" ATR exhaust tip - Alum intake pipe - NOS timing cover - chip - relocated charcoal canister - CR42's - stock

Offline puzzledfox

  • Newbie
  • *
  • Posts: 7
  • PSI: 0
  • Boost n00b
    • View Profile
Re: cold air intake
« Reply #5 on: February 21 2017, 10:18:46 AM »
Mileage will drop as the temps go lower.

Without some probes it's hard to tell if pressure in that box was higher or lower than normal.


If higher it probably won't make measurable power until you hit about 250MPH.


Thanks for enlightening me. Thinking of getting one for my ride.

Offline good2win22

  • Turbo Street Outlaw
  • *******
  • Posts: 2019
  • PSI: 0
  • No man lives happily lest he remove the boredom
    • View Profile
Re: cold air intake
« Reply #6 on: February 26 2017, 10:39:07 AM »
Nice work!
Jason

1966 Ford Ranch Wagon
1982 Jeep Wagoneer Limited
1986 Grand National BLK PHNX
1987 Turbo Regal Limited
2018 Ram 2500 Cummins

Offline aminga

  • Chicks Dig the Power Bulge
  • Turbo Street Limited
  • ***
  • Posts: 151
  • PSI: 0
  • Chicks Dig the Power Bulge
    • View Profile
Re: cold air intake
« Reply #7 on: February 28 2017, 09:32:19 AM »
I did something similar for different reasons.  I got tired of having the A/C hose rub on the filter and rub a hole in it.  Figured if the hose could rub a hole in the filter then the reverse was possible too (Giggity). 

My goal was to get the filter over toward the fender and away from the hoses.  As a plus I picked up a bung for the IAT.

I didn't build in anything to box it off.  I guess it helps some with IAT but sitting still in traffic it still climbs to over 120.




86 Regal T-type. One Owner. Twisted 6 Racing Built 109, FTSS Revolution X 206/210 Cam, T&D 1.65 Rockers, Diamond Forged Pistons, RJC Power Plate, TA6262DBB, PTE SLIC, Alkycontrol pump and Kit and ISAC Controller, Bailey TR6 Wastespark, TA Headers, ATR Downpipe, Racetronix Walbro pump and hot wire ki

Offline earlbrown

  • Moderator
  • Turbo Street Eliminator
  • ******
  • Posts: 1571
  • PSI: 6
    • View Profile
Re: cold air intake
« Reply #8 on: February 28 2017, 01:44:46 PM »
That's what I like about my MAF pipes.  They have a second articulation point you can 'steer' them down after clearing the up pipe and IAT plug.  With that additional adjustment they can miss the alternator pulley and go under the A/C lines without flexing them.

I always hated how normal pipe kits only allow for a slight height adjustment and the filter just has to land wherever it lands.
'87 GN - 4.2L SFI Turbocharged innercooled V6 - Chrome valve covers - supra pump - 14" K&N - 52mm throttlebody - rocker shaft supports -  1/2 intake spacer - TB coolant bypass - 3" ATR exhaust tip - Alum intake pipe - NOS timing cover - chip - relocated charcoal canister - CR42's - stock

Offline Grumpy

  • Turbo Street Modified
  • *****
  • Posts: 498
  • PSI: 4
    • View Profile
Re: cold air intake
« Reply #9 on: April 26 2017, 11:20:53 AM »
Without a lid it probably don't do much....

Ill bet it works better than having a lid on it  :player: Been there an done it  :rock:

 

SimplePortal 2.3.7 © 2008-2024, SimplePortal