Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - gusszgs

Pages: [1] 2 3 ... 29
1
General Buick Tech / Re: Stock Header removal
« on: March 08 2020, 11:27:29 PM »
I did, but I wanted to retain the factory look. If the crack is at the 3-5 junction, and probably is, itís a good idea to have a gusset welded in for added strength.
Check the flanges with a straight edge before install.
Any headers Iíve repaired Iíve always had the flange machined arrow straight and no gasket. Never a problem after.

2
General Buick Tech / Re: Turbo tweak Chip ?
« on: July 18 2019, 12:28:41 PM »
Like Steve said, install a TT chip, make sure compression is 145-150 on all six +- 5psi then install a vac gauge and make sure itís pulling 15-16Ē of vac.

3
General Buick Tech / Re: 60 ft blues
« on: July 15 2019, 04:12:38 PM »
Too much data and too many variables are not always a good thing.  Therefore, Stone Age it now and then  :rofl:
Very True . Some forget the basics. Easy to do really.
I'd fix the knock issue first.
 :chin:


lol....my best run ever was going via stone age. Just focused on the SM and boost........p oint n shoot

4
General Buick Tech / Re: Helping a buddy canít lower boost.
« on: May 06 2019, 01:16:17 AM »
Take a very good close look at the vacuum lines from turbo to Y

5
General Buick Tech / Re: Adjustable upper arms
« on: May 03 2019, 09:25:46 PM »
JMO, but Iím pretty happy with the adjustable UMI uppers I run. Installed properly with the right PL on the PS bar, my car not only lost .12 in the 60í, but also centered up the rear more square and I could eliminate the very small spacer I required on one side. Dropped to high 1.50ís 60í from struggling to run a 1.7 on same tire and set up.

6
For Sale/Trade/Want To Buy / Re: 1987 Buick Regal Turbo T Limited
« on: April 29 2019, 08:11:44 AM »
Any interior pics??

7
IHADAV8 Playground / Re: New T codes 32 and 44
« on: April 07 2019, 12:13:08 PM »
Thx Jason
Sneaky vacuum lines lol
Yes great feeling to have it running it think as good as a stock TR is capital of.

8
IHADAV8 Playground / Re: New T codes 32 and 44
« on: April 02 2019, 10:04:14 PM »
Thanks Steve

9
IHADAV8 Playground / Re: New T codes 32 and 44
« on: April 02 2019, 09:28:25 PM »
Just an update guys. I FINALLY got the car running to perfection!
It was a combination of a number of things but mainly a serious DS header leak ( thereís a surprise uh) poor rotted vacuum lines, injectors and dialing the tune back in. Proper gapped plugs wires ect.

Itís running absolutely fantastic!
Just a big thank to EVERYBODYíS input! The cars can certainly be a challenge at times. Itís been 5 months almost to the day since I bought this, so definitely a lot of work in her. Still lots but real sweet having it running perfectly, all parameters on SM are bang on.

10
General Buick Tech / Re: 3 year old 02
« on: April 02 2019, 11:11:40 AM »
Holy shyte bro, mine Denso 1001 has been in my Ltd for at least 10 yrs now. Still good

11
General Buick Tech / Re: Torque Plates
« on: February 28 2019, 09:50:53 AM »
I personally always like the GTX, way cool and the Ď70 Runner. My brother had a Ď70 RR 383 Magnum
That being said, the one car that gave the Mopar guys fits in those day was the STG 1 GS Buick lol
In stock form against each other, the Buick would outrun a Hemi

12
IHADAV8 Playground / Re: Filters?
« on: February 25 2019, 05:52:47 PM »
Iíve ALWAYS used Wix 51036....lots of debate.

13
IHADAV8 Playground / Re: New T codes 32 and 44
« on: February 11 2019, 04:28:28 PM »
Jim...if the crossover pipe is fukd...don't get one from Kirbans. I grabbed one from them a few years back...and it didn't come close to fitting. The studs will prolly snap. Pull the header...it ain't that hard...and install new ones. I know you don't like gaskets...but if any exhaust gases escape to the atmosphere it'll spool slower and your BLM's will be out of whack. I run both header gaskets and a turbo flange gasket. I've got 'er sealed up tight. Ya' I know. They never had gaskets...but after a gazillion heat cycles...stuff warps.

Thx, yes Iíve done the headers a number of times.
Iíll pull the crossover off and see whatís going on with the ball n flange there. I have to do the pan gasket anyway so Iíll dig in. To me it looks like some stooge has been in there trying to fix the oil leak and installed the gasket wrong, but at the rear of block you can see ALOT of the rubber gasket hanging out from the pan. Almost looks like they missed the bolt holes in the gasket lmao WTF??
 :rolleyes;

14
IHADAV8 Playground / Re: New T codes 32 and 44
« on: February 11 2019, 03:27:13 PM »
Ok, got side tracked with detailing and such but had it running again today. TT Chip installed! MAF hose is/was in good shape but yes, Iím guilty as I missed a couple of very small tares which where repaired. (Thin smear of right stuff on inner and outer surface)
Started it up this afternoon and INT is 128, BL still at 142. All other values look good.
So while prowling around under the car on jack stands looking for my source of oil leak (brand new valve covers gaskets installed) so Iíve eliminated that possibility (nice n dry up there) I discovered the exhaust IS leaking at the DS crossover. I can feel it against my hand on block side.

So, I will pull the crossover off and go from there, as it looks like I have to do the pan gasket and rear main seal anyway
Thanks to all you guys for your input. Yes, I feel like an ass!! 😂

15
General Buick Tech / Re: Intercoolers
« on: February 09 2019, 07:52:23 AM »
Way too much thinking going on. Take the car to the track and turn the alky off. Throw in Erics 112 race chip. Watch Scoobs vid on how to drain the tank faster than you can guzzle a beer. Toss a can of 112 VP in it. Drop the low gear 02's to around 780 and bump the low gear timing up. Turn the boost to 23 or higher...bring the revs up to 3000 grand on the footbrake...an d hang on for dear life. It ain't rocket science.

Can do same and turn up to 28-29 with alky and save $140 in race fuel

Pages: [1] 2 3 ... 29