Author Topic: Brad Penn oil  (Read 6860 times)

0 Members and 1 Guest are viewing this topic.

Offline Top Speed

  • Don't Tread on Me
  • Turbo Street Outlaw
  • *******
  • Posts: 2548
  • PSI: -2
    • View Profile
Brad Penn oil
« Reply #15 on: March 30 2011, 02:28:00 PM »
Quote from: "SuperSix @ Tue Mar 29, 2011 11:23 pm"
Wow. wtf.


lol!!!
Champion Irons w/T&D roller rockers, TA-61 turbo, 206/206 Comp Cam,  57 lb/hr Siemens Injectors, 3000 stall PTC, PTE Plenum w/RJC Power Plate, 70 mm Accufab Throttle Body, RJC 325 Megacooler, TurboTweak 5.7/ Alky Control w/M1 methanol, 23 psig on the street, Puddn' Power engine, Borla Exhaust

Chris

Offline SuperSix

  • Administrator
  • Turbo Street Outlaw
  • *******
  • Posts: 5071
  • PSI: 234
    • View Profile
Brad Penn oil
« Reply #16 on: March 30 2011, 03:34:40 PM »
What's your oil pressure when hot, and you can hear the tapping?
'87 GN, 60lb, TA49, THDP, FTP cam, T+ lots o' shit - SOLD
'07 Ford F150 Lariat 2WD, 5.4L 3v - 255k
'20 Kubota BX2380. FEL, 60" deck
'78 IH/Case 184 Lo-Boy
'99 Kawasaki Bayou 400 4x4

Offline $1987 GN$

  • Turbo Street Eliminator
  • ******
  • Posts: 1089
  • PSI: 1
    • View Profile
Re: Brad Penn oil
« Reply #17 on: March 31 2011, 11:15:54 PM »
http://www.autozone.com/autozone/accessories/Tools-Garage-and-Equipment/Automotive-Stethoscope/_/N-26gd

Has a variety of uses.
Or if you are good you can do like the old timers do and us a wooden stick or broom handle to narrow it down or find it.

Not sure Steve on that injector comment, late night?

Cam sensor, lifter?

AJ___

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9894
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Brad Penn oil
« Reply #18 on: April 01 2011, 09:52:29 AM »
Nope...might be his imagination that oil changed the sound....some injectors are very loud
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9894
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Brad Penn oil
« Reply #19 on: April 01 2011, 09:54:51 AM »
Most Buicks that I have seen have had some ticking noise from somewhere....I don't pay attention unless it suddenly gets worse or a different sound shows up...no use spending your life wondering if it is a piston pin or windshield wiper bearing
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline $1987 GN$

  • Turbo Street Eliminator
  • ******
  • Posts: 1089
  • PSI: 1
    • View Profile
Brad Penn oil
« Reply #20 on: April 01 2011, 11:10:12 AM »
Quote from: "Steve Wood @ Fri Apr 01, 2011 8:54 am"
Most Buicks that I have seen have had some ticking noise from somewhere....I don't pay attention unless it suddenly gets worse or a different sound shows up...no use spending your life wondering if it is a piston pin or windshield wiper bearing


Agreed

AJ___

Offline ULYCYC

  • Turbo Street Modified
  • *****
  • Posts: 870
  • PSI: 4
    • View Profile
Re: Brad Penn oil
« Reply #21 on: April 01 2011, 11:10:57 AM »
Try and run the engine with the Serpentine belt removed. Bad belt or idler pulley can make the same noise.
ED BAKER
87-T, Maplight equipped rear view mirror..
01 Park Ave Ultra S\'charged
BPG#1458

Offline Shimy87

  • Turbo Street Eliminator
  • ******
  • Posts: 1238
  • PSI: 2
    • View Profile
Re: Brad Penn oil
« Reply #22 on: April 01 2011, 11:14:06 AM »
Oil pressure is good ( 50 warm and crusing) and its not an injector, I know that sound. I did try the long screwdriver trick held to my ear and checking around, no luck. Pulled the valve covers and held my hand on each rocker to see if I could feel anything or hear a change in noise...no luck. I kinda ended up where what Steve said, it just makes some noise and I gotta quit worring about it. Cant wait for the salt to get rained off the roads here so I can get it back out again!!

Want to get rid of the Flowmaster exhaust this spring and get the Pypes cat back system installed.

Thanks alot guys!!!
87 GN, K&N cold air, gutted cat, TT 5.7 chip, AFPR, 340 Walbro w/ hotwire, 60 LBS injectors, 981 valve springs, 206/206 Cam, RJC Powerplate, LS1 MAF & translator, Vacuum brakes, Hellwig rear sway bar, Energy suspension poly bushings, Razors Alky, Pypes exhaust, 5931 turbo, CK9.5 converter

 

SimplePortal 2.3.7 © 2008-2024, SimplePortal