Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Norm340

Pages: [1] 2 3
2
General Buick Tech / Re: ATTN: Steve, RE: Alternator Rebuild Kit
« on: November 08 2021, 12:15:55 PM »
UPDATE: Seller offers the correct kit for early model also.

Do you have a link for that kit?

3
General Buick Tech / Re: U Joint Question
« on: November 06 2021, 08:59:30 PM »
Will do, thanks very much!

4
General Buick Tech / U Joint Question
« on: November 06 2021, 12:07:55 PM »
I know, I should have asked this question before I ordered these but....

Would these U joints from Rock Auto be the correct ones for a 87 GN?

Thanks
Norm

ACDELCO 45U0110 {#89029292} (Heavy Duty) Greaseable Super Strength Info
Fits At Transmission; Inside Lock Rings
or at Rear Axle; Inside Lock Rings

https://www.rockauto.com/en/catalog/buick,1987,regal,3.8l+231cid+v6+turbocharged,1020957,drivetrain,universal+joint,2392


5
General Buick Tech / Re: ICM Question
« on: April 21 2021, 07:01:30 PM »
I bought the Genuine GM D1996, Haven't installed.
Just thought I should have one in stock just in case...LOL

FYI: came with a  new coil gasket and mounting screws

6
Thanks Steve.    :cheers:

7
Steve....

Don't suppose you could upload the Buick front end wallpaper, It looks good!


Thanks
Norm

8
General Buick Tech / Re: ICM Question
« on: February 08 2021, 06:14:41 PM »
Thanks for the info

 :cheers:

9
General Buick Tech / ICM Question
« on: February 07 2021, 11:05:20 AM »
Was looking on Rock Auto for an Ign Control Module for the 87 GN and was wondering...
What is a Magnavox unit?
Thanks

GM GENUINE D1996 {#19260720, 24503624} Info
FitsW/MAGNAVOX UNIT; WITH MAGNAVOX UNIT
orwith Magnavox Type I Ignition System


13
IHADAV8 Playground / The Day a V6 ran in Pro Stock
« on: September 24 2020, 12:16:29 PM »
https://youtu.be/nkxr0CPiZGY?t=80

Love the comment from the announcer in the final
Its 268 Cubic inches against a refrigerator under the hood of Glidden's Car...LOL   

14
General Buick Tech / Re: Rear Control Arms
« on: September 15 2020, 12:32:52 PM »
Thanks you guys.

Earl: I'll follow those instructions.

Brad: I have a squeak coming from one of those bushings and
have 4 new ones just sitting in the tool box so I thought lets have a look.
UMI says due to high demand it may take 4-5 weeks so I might check them out again just before spring.

 :atbeer: :atbeer:

15
General Buick Tech / Rear Control Arms
« on: September 14 2020, 07:50:31 PM »
Hey Guys

If I was going to remove the lower control arm to replace the bushings.
Is there a certain way to remove the lower arms?
Like having jack stands under the frame and the floor jack under the diff then loosen the bolts.
Maybe only remove one arm at a time, is there tension on the sway bar?
That kind of stuff.

Kinda know how to remove and install the bushings but the arms not so much.

Thanks

Pages: [1] 2 3
SimplePortal 2.3.7 © 2008-2024, SimplePortal