Author Topic: Need Quick Help On Launching A Stocker!  (Read 3873 times)

0 Members and 1 Guest are viewing this topic.

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5557
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Need Quick Help On Launching A Stocker!
« on: July 15 2016, 11:57:09 AM »
This is one of the locals who actually listens...and he's coming out with me tonite. This is a fresh engine from JB Racing that Dan installed. It's bone stock and will be running 94 Sunoco tonite at the stock boost level. Chip and injectors are new from Eric...AFPR... boost gauge...SM. It was a peg leg and it now has a posi in it. Rear sway bar is stock...but it has air bags. I'm handcuffed...c uz he informed me he's using 26 inch TA radials. I need help with a tire pressure to run and what pressure to run in the air bags. Stock turbo...stock convertor. The track will be empty...so I'll have plenty of practice runs with it. I don't think it has line lock. I'm unsure of the shocks he's running at all 4 corners. I'm gonna have him run it WFO till the 1/8th...and get out of it...and check the 02's. I'm gonna sit in the passenger seat and watch the SM for KR. If all's well, I'll let him run it through the 1/4. Fuel pump is new with a hotwire kit. Fuel supply should be fine. Open to suggestions to launch it.





Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline Joe Buick

  • Bone Stock
  • **
  • Posts: 41
  • PSI: 0
  • Boost n00b
    • View Profile
Re: Need Quick Help On Launching A Stocker!
« Reply #1 on: July 15 2016, 12:47:51 PM »
On Radials!!! 18-20 psi
NOT more than 5 psi launches. Already they will be up in smoke.
You know the rest.. :rock:
JB RACING

Offline Shimy87

  • Turbo Street Eliminator
  • ******
  • Posts: 1238
  • PSI: 2
    • View Profile
Re: Need Quick Help On Launching A Stocker!
« Reply #2 on: July 15 2016, 12:50:48 PM »
any track prep? As you know I don't have good tires either. If no prep I'd guess you will be lucky to leave with much more than 1-2 lbs of boost. If there is some sticky put down mine would hook 3-4 lb launches before I started adding upgrades
87 GN, K&N cold air, gutted cat, TT 5.7 chip, AFPR, 340 Walbro w/ hotwire, 60 LBS injectors, 981 valve springs, 206/206 Cam, RJC Powerplate, LS1 MAF & translator, Vacuum brakes, Hellwig rear sway bar, Energy suspension poly bushings, Razors Alky, Pypes exhaust, 5931 turbo, CK9.5 converter

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5557
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Re: Need Quick Help On Launching A Stocker!
« Reply #3 on: July 15 2016, 01:19:24 PM »
Track prep is hit and miss on one of these practice evenings.
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5557
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Re: Need Quick Help On Launching A Stocker!
« Reply #4 on: July 15 2016, 01:29:12 PM »
It also has an RJC 3 inch DP. I couldn't talk him out of it. :)
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline motorhead

  • Turbo Street Outlaw
  • *******
  • Posts: 2265
  • PSI: 4
  • look at my balls... look at them!!!
    • View Profile
Re: Need Quick Help On Launching A Stocker!
« Reply #5 on: July 15 2016, 02:24:08 PM »
I would bring it up against the converter to take the slack out of the drivetrain, and on the last yellow flat foot it.  Chances are it will be laggy enough for the first 60' it won't roast the tires, but will have good momentum.  As for tire pressure (assuming the rubber isn't hockey puck hard) I would do a short burnout in the parking lot to see if the tires are cupping or over inflated, adjust the pressure until the contact patch is black across the board.  No need for John Force burnouts - other than for fun of course!
>>>Das Instagram<<<
'80 LeMans Wagon|'87 Monte Carlo SS|'92 Camaro Z28|'07 TrailBlazer SS|'15 Colorado Z71|'19 Hellcat Widebooty M6

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5557
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Re: Need Quick Help On Launching A Stocker!
« Reply #6 on: July 15 2016, 02:51:10 PM »
Okay guys...heading out. We'll try everytbing suggested.
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5557
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Re: Need Quick Help On Launching A Stocker!
« Reply #7 on: July 15 2016, 11:01:27 PM »
Don did pretty well tonite...with a tire smoking 13.5x at 104x. High gear 02's were pig rich in the 870's.
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline Shimy87

  • Turbo Street Eliminator
  • ******
  • Posts: 1238
  • PSI: 2
    • View Profile
Re: Need Quick Help On Launching A Stocker!
« Reply #8 on: July 15 2016, 11:31:12 PM »
 :rock:
87 GN, K&N cold air, gutted cat, TT 5.7 chip, AFPR, 340 Walbro w/ hotwire, 60 LBS injectors, 981 valve springs, 206/206 Cam, RJC Powerplate, LS1 MAF & translator, Vacuum brakes, Hellwig rear sway bar, Energy suspension poly bushings, Razors Alky, Pypes exhaust, 5931 turbo, CK9.5 converter

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
Need Quick Help On Launching A Stocker!
« Reply #9 on: July 16 2016, 12:57:14 AM »
Cool it will only get faster. How did it 60' on street tires?
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5557
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Re: Need Quick Help On Launching A Stocker!
« Reply #10 on: July 16 2016, 07:59:55 AM »
Larry, he got there late...and I was busy with the BS with my car. I watched all 3 of his runs. 13.8, 13.6 and 13.5. He races a 6 second snowmoblie in the 1/8th during the winter that runs 135 MPH on the big end. Don knows how to 'pedal' a car. He had it down cold by the third run.
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline TexasT

  • Legend in my own mind
  • Turbo Street Outlaw
  • *******
  • Posts: 2170
  • PSI: 1
  • So, This black car is fast?
    • View Profile
Re: Need Quick Help On Launching A Stocker!
« Reply #11 on: July 16 2016, 09:15:46 AM »
It has decent mph for a stock unit. With traction it will do 13.0s. Maybe he had a good time and will spring for some tires to hook it up.
Rich

"Goals without actions are just dreams."

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9893
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Need Quick Help On Launching A Stocker!
« Reply #12 on: July 16 2016, 09:35:52 AM »
Not bad for being that rich
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

 

SimplePortal 2.3.7 © 2008-2024, SimplePortal