« previous next »
Pages: [1]   Go Down

Author Topic: turbo oil feed line  (Read 5521 times)

0 Members and 1 Guest are viewing this topic.

Offline Be4u

  • Turbo Street Outlaw
  • *******
  • Posts: 3548
  • PSI: 0
    • View Profile
    • http://www.cardomain.com/memberpage/400586
turbo oil feed line
« on: July 16 2005, 06:29:32 PM »
Sitting here looking at my oil feed line to the turbo I noticed it comes pretty close to the header AND header heat shield. The line is stock. Would that cause c
Logged
Save the bumper fillers!
Move to Canadia!

Offline Recklessrob

  • Turbo Street Outlaw
  • *******
  • Posts: 5112
  • PSI: 3
    • View Profile
Re: turbo oil feed line
« Reply #1 on: July 17 2005, 01:18:58 AM »
You could wrap the line in some of that woven fiberglass
sleeving that Summit sells for ignition wires and stuff. :idea;
Logged
Rob

Offline JP87GN

  • Bone Stock
  • **
  • Posts: 11
  • PSI: 0
    • View Profile
Re: turbo oil feed line
« Reply #2 on: July 17 2005, 01:07:47 PM »
To remove yours just find a wrench or adjustable wrench to fit the square part of the sensor block and hold it while you bust the line loose. The white jiz is just teflon thread sealer and you can use teflon tape, Its a tapered flare fit so it should not leak.
Logged
86 T-Type daily driver

Offline Be4u

  • Turbo Street Outlaw
  • *******
  • Posts: 3548
  • PSI: 0
    • View Profile
    • http://www.cardomain.com/memberpage/400586
Re: turbo oil feed line
« Reply #3 on: July 18 2005, 12:13:08 AM »
I took my new oil feed line and bent it and reshaped it. I think I did a hella good job for never bending tubing b4. Both ends line up perfectly! I'll post pics tomorrow.
Logged
Save the bumper fillers!
Move to Canadia!

Offline Be4u

  • Turbo Street Outlaw
  • *******
  • Posts: 3548
  • PSI: 0
    • View Profile
    • http://www.cardomain.com/memberpage/400586
Re: turbo oil feed line
« Reply #4 on: July 18 2005, 07:37:31 PM »
heres a b4 and after.
Logged
Save the bumper fillers!
Move to Canadia!

Offline SuperSix

  • Administrator
  • Turbo Street Outlaw
  • *******
  • Posts: 5071
  • PSI: 234
    • View Profile
Re: turbo oil feed line
« Reply #5 on: July 18 2005, 10:16:04 PM »
Good job!
Logged
'87 GN, 60lb, TA49, THDP, FTP cam, T+ lots o' shit - SOLD
'07 Ford F150 Lariat 2WD, 5.4L 3v - 255k
'20 Kubota BX2380. FEL, 60" deck
'78 IH/Case 184 Lo-Boy
'99 Kawasaki Bayou 400 4x4

Offline 87natty

  • Turbo Street Outlaw
  • *******
  • Posts: 3616
  • PSI: 0
    • View Profile
    • http://www.wix.com/lynch455/science
turbo oil feed line
« Reply #6 on: July 19 2005, 04:33:28 AM »
You stud.
Logged
My 1958 Mamiya can beat up whatever camera you just wasted your money on.

Offline Recklessrob

  • Turbo Street Outlaw
  • *******
  • Posts: 5112
  • PSI: 3
    • View Profile
Re: turbo oil feed line
« Reply #7 on: July 19 2005, 12:42:42 PM »
Looks good.  :atbeer:
Logged
Rob

Offline Be4u

  • Turbo Street Outlaw
  • *******
  • Posts: 3548
  • PSI: 0
    • View Profile
    • http://www.cardomain.com/memberpage/400586
Re: turbo oil feed line
« Reply #8 on: July 19 2005, 01:33:36 PM »
Thank you thank you! :yawinkle:
Logged
Save the bumper fillers!
Move to Canadia!
Pages: [1]   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2024, SimplePortal