« previous next »
Pages: [1]   Go Down

Author Topic: rigid intake pipe with stock maf  (Read 2995 times)

0 Members and 1 Guest are viewing this topic.

Offline dyermullet

  • Turbo Street Limited
  • ***
  • Posts: 159
  • PSI: 0
  • Boost n00b
    • View Profile
rigid intake pipe with stock maf
« on: March 26 2015, 07:06:47 PM »
What are my options?   After 10 years my flexible tube has finally failed.  I have a stock sized turbo inlet bell, and am running a stock maf sensor.  I would prefer a bent pipe, and not a straight pipe with angled couplings, but I would be ok with that also.
Logged

Offline TexasT

  • Legend in my own mind
  • Turbo Street Outlaw
  • *******
  • Posts: 2170
  • PSI: 1
  • So, This black car is fast?
    • View Profile
Re: rigid intake pipe with stock maf
« Reply #1 on: March 26 2015, 08:10:20 PM »
I have the later but have eyed the s shaped ones on eBay. I also run a stock maf.


http://m.ebay.com/itm/180799202057?nav=SEARCH

Logged
Rich

"Goals without actions are just dreams."

Offline earlbrown

  • Turbo Street Eliminator
  • ******
  • Posts: 1571
  • PSI: 6
    • View Profile
Re: rigid intake pipe with stock maf
« Reply #2 on: March 27 2015, 12:27:51 AM »
How about one that's half way there?...






The reason I went with the one bend and the angled coupler was to be able to 'steer' the pipe and MAF at whatever angle you want while still clearing the IAC plug and the uppipe.  It's not as important on the 3" as the 3.5" but it really helps those people that run 3" up pipes too.
Logged
'87 GN - 4.2L SFI Turbocharged innercooled V6 - Chrome valve covers - supra pump - 14" K&N - 52mm throttlebody - rocker shaft supports -  1/2 intake spacer - TB coolant bypass - 3" ATR exhaust tip - Alum intake pipe - NOS timing cover - chip - relocated charcoal canister - CR42's - stock

Offline dyermullet

  • Turbo Street Limited
  • ***
  • Posts: 159
  • PSI: 0
  • Boost n00b
    • View Profile
Re: rigid intake pipe with stock maf
« Reply #3 on: March 27 2015, 08:20:48 AM »
Did you buy this or make yourself?
Logged

Offline earlbrown

  • Turbo Street Eliminator
  • ******
  • Posts: 1571
  • PSI: 6
    • View Profile
Re: rigid intake pipe with stock maf
« Reply #4 on: March 27 2015, 01:59:21 PM »
That's one of mine. I also have it in 3.5" but you'd need an LS1 MAF since it won't work with a stock MAF.

The pipe shown is for a LT1 or stock MAF.  Multi-ply silicone boost hoses (overkill), alum pipe, and stainless steel T-bolt clamps. (and the ability to keep it off the up pipe and IAC plug)

 

If you like it I can do $110 to your door in the lower 48
Logged
'87 GN - 4.2L SFI Turbocharged innercooled V6 - Chrome valve covers - supra pump - 14" K&N - 52mm throttlebody - rocker shaft supports -  1/2 intake spacer - TB coolant bypass - 3" ATR exhaust tip - Alum intake pipe - NOS timing cover - chip - relocated charcoal canister - CR42's - stock

Offline Top Speed

  • Don't Tread on Me
  • Turbo Street Outlaw
  • *******
  • Posts: 2548
  • PSI: -2
    • View Profile
Re: rigid intake pipe with stock maf
« Reply #5 on: March 28 2015, 12:06:06 PM »
That looks real nice, Earl.
Logged
Champion Irons w/T&D roller rockers, TA-61 turbo, 206/206 Comp Cam,  57 lb/hr Siemens Injectors, 3000 stall PTC, PTE Plenum w/RJC Power Plate, 70 mm Accufab Throttle Body, RJC 325 Megacooler, TurboTweak 5.7/ Alky Control w/M1 methanol, 23 psig on the street, Puddn' Power engine, Borla Exhaust

Chris

Offline Forzfed

  • Turbo Street Eliminator
  • ******
  • Posts: 1337
  • PSI: 5
  • Boost n00b
    • View Profile
Re: rigid intake pipe with stock maf
« Reply #6 on: April 02 2015, 12:17:23 PM »
 :yeah: :yeah:   Good job, Earl. :cheers:
Logged
Pages: [1]   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2024, SimplePortal