Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Charlief1

Pages: 1 2 [3] 4 5 ... 90
31
General Buick Tech / Re: Richard Clark's
« on: April 28 2016, 12:49:56 AM »
Send me an address Gary. :D You want ribs or a brisket? The links are included. :rock: Make sure to stop at Ray's place and share though. :cheers:

32
General Buick Tech / Re: Richard Clark's
« on: April 27 2016, 12:10:52 AM »
If I could I would Gary. If you go tell me and I'll see if I can ship some treats your way. :rock:

33
IHADAV8 Playground / Re: Barn motor and tranny swap
« on: April 26 2016, 12:49:16 AM »
Hopefully you killed a few skeeters Jason :rofl:

34
IHADAV8 Playground / Re: Barn motor and tranny swap
« on: April 25 2016, 01:52:31 AM »
     
I have 2.5" in total
There are operations that can help with that Steve. :rofl: TB3 told me about them. :O

Let me know how it works out for you!  :D
They don't have an operation to shorten things Steve, unless you've created one. :rofl:

Congrats Jason. :cheers:

Glad that centimeter ruler has brought you so much pleasure
But the metric micrometer didn't register for you Steve. What's up with that? :wtf: Should I fire up the the electron microscope? :rofl:

35
IHADAV8 Playground / Re: Barn motor and tranny swap
« on: April 24 2016, 12:54:36 AM »
     
I have 2.5" in total
There are operations that can help with that Steve. :rofl: TB3 told me about them. :O

Let me know how it works out for you!  :D
They don't have an operation to shorten things Steve, unless you've created one. :rofl:

Congrats Jason. :cheers:

36
IHADAV8 Playground / Re: Barn motor and tranny swap
« on: April 23 2016, 12:59:05 AM »
I have 2.5" in total
There are operations that can help with that Steve. :rofl: TB3 told me about them. :O

37
General Buick Tech / Re: Roller cam options
« on: April 22 2016, 12:14:31 AM »
I have always been told that it was usually fine to install up to 0.516" lift on stock heads with stock rocker ratios but I would always also advise that one check the clearance to the valve guide just in case your heads are the exception to the rule. 
I did some checking on several heads that I had Steve and you can't run more than .490 lift, period. That's why edeLcrap has their 204/214 CAM AT .478.

38
You'll be in trouble later cause you got a little pussy on the side. :rofl: You knew someone would say it. :icon_fU:

39
IHADAV8 Playground / Re: 2016 at Maple Grove
« on: April 17 2016, 01:24:24 PM »
Good luck Gary.

40
IHADAV8 Playground / Re: Watch for a surprise
« on: April 12 2016, 12:50:42 PM »
That's supposed to be around flower mound so it's close to home.

41
IHADAV8 Playground / Watch for a surprise
« on: April 12 2016, 12:10:41 AM »
This vid will give all a surprise but it's here in Texas from the info I've got.

http://texasfishingforum.com/forums/ubbthreads.php/topics/11534337/This_was_not_a_catfish...#Post11534337

42
You might try some stereo 10 ga since it's got super fine wire in it. It may be the best of both worlds. :hmm

43
IHADAV8 Playground / Re: Still looking for a Rebel
« on: April 10 2016, 11:44:53 PM »
Don't even think of changing the radio Gary. If things were that simple now I'd be very happy. :rock: Very cool ride. :cheers:

44
IHADAV8 Playground / Re: Barn motor and tranny swap
« on: April 09 2016, 11:39:54 PM »
Grow the stash back Rich. :player: What size is the converter Jason?

45
IHADAV8 Playground / Re: Barn motor and tranny swap
« on: April 07 2016, 01:20:15 AM »
Got a tranny jack as well as an adapter for a floor jack, if you need to borrow them Jason. :rock: Send me a note if you  do. :cheers:

Pages: 1 2 [3] 4 5 ... 90
SimplePortal 2.3.7 © 2008-2024, SimplePortal