Author Topic: Home Made Wiring Rant  (Read 1864 times)

0 Members and 1 Guest are viewing this topic.

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5557
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Home Made Wiring Rant
« on: June 01 2013, 08:39:47 AM »
I'm getting really effen tired of this. People nickel and diming trying to make their own hot wire kits...duel fuel pump kits...hot wire injector kits...etc...w ho don't know a volt from an ohm. Latest fiasco. I contacted Steve Wood about a car that came into the shop. We did a vacuum brake conversion. Shortly after...the car's idle is over 1,000. Turns out it's a burnt fuse... and it's got several...for some reason...in some trumped up home made dual in tank pump kit. Install a good fuse...normal idle. Pull the fuse...the idle screams. It's getting to the the point that the only TR I wanna work on...is my own.
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9893
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Home Made Wiring Rant
« Reply #1 on: June 01 2013, 09:15:41 AM »
after 25 years of adding/removing stuff to the one I bought new in '86, I don't have a clue what all the wiring is...and I have taken the side cutters to it at least three times trying to clean it up.

The one I bought back in '99 for my son had messed up wiring and I took my side cutters out and removed four different alarm systems that had been installed on it by po's, discovered an external pump in front of the fuel tank that was wired directly to the fuse block with no relay plus a whole bunch of other things.  Then there was the El Camino that I bought that had been wired with lamp wire...yes, the kinda wire that you plug the lamp into the wall with.  Someone had installed power locks, alarm, etc and lamp wire was his choice of wiring.  I cut about 30 lbs of wiring out of that car before I found why it did not want to turn over.

Side cutters are my best friend

It is frustrating trying to help someone that does not know an amp from an ohm....I think E=IR went out of existence along with crystal set radios
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline SuperSix

  • Administrator
  • Turbo Street Outlaw
  • *******
  • Posts: 5071
  • PSI: 234
    • View Profile
Re: Home Made Wiring Rant
« Reply #2 on: June 03 2013, 05:00:58 PM »
Steve loves the dykes.
'87 GN, 60lb, TA49, THDP, FTP cam, T+ lots o' shit - SOLD
'07 Ford F150 Lariat 2WD, 5.4L 3v - 255k
'20 Kubota BX2380. FEL, 60" deck
'78 IH/Case 184 Lo-Boy
'99 Kawasaki Bayou 400 4x4

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9893
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Home Made Wiring Rant
« Reply #3 on: June 03 2013, 06:02:05 PM »
put my thumb in everyone I see
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline daveismissing

  • Two Buicks- too little money$$
  • Turbo Street Outlaw
  • *******
  • Posts: 6515
  • PSI: 3
  • Two Buicks- too little money$$
    • View Profile
Re: Home Made Wiring Rant
« Reply #4 on: June 03 2013, 07:35:10 PM »
-Drain plug by Earl Brown, custom oil pan by Rich's Auto

 

SimplePortal 2.3.7 © 2008-2024, SimplePortal