Author Topic: nocooler's firechicken thread  (Read 236631 times)

0 Members and 8 Guests are viewing this topic.

Offline TexasT

  • Legend in my own mind
  • Turbo Street Outlaw
  • *******
  • Posts: 2170
  • PSI: 1
  • So, This black car is fast?
    • View Profile
Re: nocooler's firechicken thread
« Reply #660 on: April 05 2019, 05:55:25 PM »
From the Holley message forum they post of a usb hub and a Bluetooth dongle to do Bluetooth. I wasn't sure just what is being used here but the ones I looked at on the Holley site didn't have that feature out of the box.
Rich

"Goals without actions are just dreams."

Offline nocooler

  • Administrator
  • Turbo Street Eliminator
  • ******
  • Posts: 1786
  • PSI: 3
    • View Profile
Re: nocooler's firechicken thread
« Reply #661 on: April 08 2019, 03:16:13 PM »
Couple steps forward and a couple sideways.
Driveshaft is ordered!
Trans cooler is so big it doesn’t fit out front, it’s a double stacked cooler with a fan. It fits nice under the floor where it was previous installed. It fits perfectly there - but no room for the exhaust. Back to considering fender exit. Makes everything easier, and it’s no worse than dumping the exhaust under the car, both in noise and fume wise.
It appears the fitting in the trans vent is to tight to the case to put the hose end on. And of course it’s to tight to the floor mess with. Hopefully I can lower the kmember and trans crossmember enough to fix it. If not trans needs to come back out.

Spent Sunday afternoon retuning my brother 07 Grand Prix gt w/3800 supercharged v6. We leaned it up and ended up dropping the timing down to 10* @ wot and the damn thing still knocked. After 2-3 pulls the blower car is so heat soaked that we called it a day. I think 8* might be what it takes. If the Maf wasn’t built into the throttle body I think we’d try spraying it with some washer fluid.
IhaveaV8

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9882
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: nocooler's firechicken thread
« Reply #662 on: April 09 2019, 09:33:09 AM »
How long will it take to get the new driveshaft?
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline nocooler

  • Administrator
  • Turbo Street Eliminator
  • ******
  • Posts: 1786
  • PSI: 3
    • View Profile
Re: nocooler's firechicken thread
« Reply #663 on: April 09 2019, 09:53:02 AM »
Probably be here toward the end of the week. Coming from PEM in MO
IhaveaV8

Offline nocooler

  • Administrator
  • Turbo Street Eliminator
  • ******
  • Posts: 1786
  • PSI: 3
    • View Profile
Re: nocooler's firechicken thread
« Reply #664 on: April 09 2019, 11:44:11 AM »
It’s Oh and it’s supposed to snow Thursday - it was 70f yesterday
IhaveaV8

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9882
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: nocooler's firechicken thread
« Reply #665 on: April 09 2019, 02:17:30 PM »
another bomb cyclone.  It's supposed to reach the Texas Panhandle.  forecasting 39 low Saturday night here. Gonna hit low 90's here today
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline Forzfed

  • Turbo Street Eliminator
  • ******
  • Posts: 1337
  • PSI: 5
  • Boost n00b
    • View Profile
Re: nocooler's firechicken thread
« Reply #666 on: April 09 2019, 03:56:50 PM »
It’s Oh and it’s supposed to snow Thursday - it was 70f yesterday
That is summer weather here!  We had snow on the ground when I woke up this afternoon. :( It was 10F this morning.

Offline nocooler

  • Administrator
  • Turbo Street Eliminator
  • ******
  • Posts: 1786
  • PSI: 3
    • View Profile
Re: nocooler's firechicken thread
« Reply #667 on: April 17 2019, 10:10:45 AM »
Driveshaft is here. The center to center measurement is right where I expected it to land, I only gave them the tran seal to center measurement. Fingers crossed it'll fit.


It's not as pretty as my PST driveshaft was, but I guess I won't feel like as much as an asshole when I slide it across the floor and scratch it all up.


Of course I'm busy pretty much the rest of the week, so maybe this weekend I'll be able to check it out. I've been working on stuff around the house, so I haven't made any progress on the car. Hopefully next week the weather will calm down.

IhaveaV8

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9882
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: nocooler's firechicken thread
« Reply #668 on: April 17 2019, 11:30:09 AM »
well hurry up!  Now that Brad has retired, you are my only hope for a life!  :D
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5549
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Re: nocooler's firechicken thread
« Reply #669 on: April 17 2019, 11:55:03 PM »
well hurry up!  Now that Brad has retired, you are my only hope for a life!  :D


Jason and Jeremy are the youngsters I'm keeping an eye on.
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline nocooler

  • Administrator
  • Turbo Street Eliminator
  • ******
  • Posts: 1786
  • PSI: 3
    • View Profile
Re: nocooler's firechicken thread
« Reply #670 on: April 22 2019, 11:54:04 AM »
Driveshaft fits....



IhaveaV8

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9882
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: nocooler's firechicken thread
« Reply #671 on: April 22 2019, 12:50:34 PM »
Money can fix a lot of things!  Nice looking!
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline nocooler

  • Administrator
  • Turbo Street Eliminator
  • ******
  • Posts: 1786
  • PSI: 3
    • View Profile
Re: nocooler's firechicken thread
« Reply #672 on: April 22 2019, 02:47:18 PM »
It got a few scratches going in. I knew it was going to work when I had to work a little bit to get it in.
One step closer.
IhaveaV8

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9882
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: nocooler's firechicken thread
« Reply #673 on: April 22 2019, 07:36:43 PM »
 :cheers: :cheers:
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5549
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Re: nocooler's firechicken thread
« Reply #674 on: April 22 2019, 07:38:49 PM »
What's left?
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

 

SimplePortal 2.3.7 © 2008-2024, SimplePortal