« previous next »
Pages: [1]   Go Down

Author Topic: Mease stock location intercooler  (Read 2679 times)

0 Members and 1 Guest are viewing this topic.

Offline poppy1440

  • Bone Stock
  • **
  • Posts: 68
  • PSI: 0
    • View Profile
Mease stock location intercooler
« on: February 14 2016, 03:32:23 AM »
Hello,  the previous owner of my car apparently cut the side of the intercooler shourd in order for the front sway bar to fit.
I have a HR Bar at and have no intentions on re-installing the front bar.

My question is besides for cosmetic reasons, will I benefit anything from fabricating something to close in the sides or finding something to close in the sides.
Thanks
Logged
86 gn. Champion irons, roller cam,stock location stretch intercooler, 3" exhaust," DP, scan master, red Armstrong  pump hot wired,  60 lbs injectors, Razors' alky kit, 6265, 6.0 chip, powerlogger, plx-afr, mt 275/50r15 et street

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9893
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Mease stock location intercooler
« Reply #1 on: February 14 2016, 09:23:20 AM »
Doubt it

Sent from my LG-H810 using Tapatalk

Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline motorhead

  • Turbo Street Outlaw
  • *******
  • Posts: 2265
  • PSI: 4
  • look at my balls... look at them!!!
    • View Profile
Re: Mease stock location intercooler
« Reply #2 on: February 14 2016, 10:22:37 AM »
Notching the shroud is normal with that intercooler as I recall.  So do what you feel is best for you.
Logged
>>>Das Instagram<<<
'80 LeMans Wagon|'87 Monte Carlo SS|'92 Camaro Z28|'07 TrailBlazer SS|'15 Colorado Z71|'19 Hellcat Widebooty M6

Offline daveismissing

  • Two Buicks- too little money$$
  • Turbo Street Outlaw
  • *******
  • Posts: 6515
  • PSI: 3
  • Two Buicks- too little money$$
    • View Profile
Re: Mease stock location intercooler
« Reply #3 on: February 14 2016, 11:02:20 AM »
Interesting . At what speed would we say the the air pushed by the MPH dominates the pull from that little fan?
Logged
-Drain plug by Earl Brown, custom oil pan by Rich's Auto

Offline Just a Six?

  • OK Now who Farted??
  • Turbo Street Eliminator
  • ******
  • Posts: 1252
  • PSI: 2
    • View Profile
Re: Mease stock location intercooler
« Reply #4 on: February 14 2016, 11:29:31 AM »
I have a Precision & it comes cut for the front bar with some adjustable plates that screw on. I messed them up & made a couple new ones. Used it closed up for years & now open with a hollow front bar & no difference I can tell? I haven't used the stock fan since I got it either.
Logged
David
87 LTD. Purchased May 88
Doeskin leather, coach lites without Landau Roof, moon roof, carpeted trunk & No Factory Hood Ornament!
The sticker on AC shows a V-8 Carb car. Special order by Mr. Nick Hall VP of GM Canada
Runs 11.50 on 21 lbs with my old style 67 Q Trim & Alchy

Offline motorhead

  • Turbo Street Outlaw
  • *******
  • Posts: 2265
  • PSI: 4
  • look at my balls... look at them!!!
    • View Profile
Re: Mease stock location intercooler
« Reply #5 on: February 14 2016, 12:07:45 PM »
Logging your IATs on the outlet side before/after would be all you need to do.
Logged
>>>Das Instagram<<<
'80 LeMans Wagon|'87 Monte Carlo SS|'92 Camaro Z28|'07 TrailBlazer SS|'15 Colorado Z71|'19 Hellcat Widebooty M6

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9893
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Mease stock location intercooler
« Reply #6 on: February 14 2016, 01:54:51 PM »
It would be difficult to prove any advantages connected to the factory fan.  KB once had an IC fan shroud that was intended to enable it to draw air thru the IC rather than the adjacent air. 
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline poppy1440

  • Bone Stock
  • **
  • Posts: 68
  • PSI: 0
    • View Profile
Re: Mease stock location intercooler
« Reply #7 on: February 14 2016, 05:40:48 PM »
Thanks
Logged
86 gn. Champion irons, roller cam,stock location stretch intercooler, 3" exhaust," DP, scan master, red Armstrong  pump hot wired,  60 lbs injectors, Razors' alky kit, 6265, 6.0 chip, powerlogger, plx-afr, mt 275/50r15 et street

Offline tb3

  • Turbo Street Eliminator
  • ******
  • Posts: 1447
  • PSI: 2
    • View Profile
Re: Mease stock location intercooler
« Reply #8 on: February 14 2016, 10:37:32 PM »
I had one of them ken belle intercooler shrouds.  Was a nice tight fit around the fan. 
I was told it was actually a restriction for the air going through it once you get over about 40 mph, but not sure if thats true or not
Logged
When I'm in Rome, they do as I do
Pages: [1]   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2024, SimplePortal