Messages

121

General Buick Tech / Re: I was wrong but now we are getting somewhere!

« on: August 18 2013, 03:43:11 PM »

you don't have to replace anything, just the injectors and re flash the chip

122

General Buick Tech / Re: I was wrong but now we are getting somewhere!

« on: August 18 2013, 02:10:26 PM »

Well if you think its fine the way it is then don't go and bi anything and just leave it alone.Steve trying to sort out your car and now you say its fine, what is it then?

123

General Buick Tech / Re: VR1-20/50

« on: August 18 2013, 12:45:14 AM »

Steve i did't see the oil pressure when the car was running because i was getting gas out, but the car sounded really good has for the metal in the pan the pan has never been off the car and for the injectors in the car here's the numbers 621038 they do have a red ring around them and for the chip hes going to answer that one.   

124

General Buick Tech / Re: VR1-20/50

« on: August 18 2013, 12:15:13 AM »

Rest a easy guys, I went to his house and look at the car and heard it run and there nothing wrong he has a few noisy lifters that you cant really hear them, Bill told him he might have 36lb injectors but no there red strip and there 38lb and he has a TT chip for 009. so there you go also the clacking at the front is his belt tensioner. End of report. 

125

General Buick Tech / Re: VR1-20/50

« on: August 17 2013, 06:37:22 AM »

Phone me at this number 905-447-9603 .

126

General Buick Tech / Re: VR1-20/50

« on: August 16 2013, 10:54:25 PM »

I toll him to phone me,but you know they don't listen o well.

127

General Buick Tech / Re: Freshen up a motor

« on: August 14 2013, 03:32:07 PM »

If you took off the pan and it sat around for a hour or two, What could have fallen into it? Was any body working with gold flakes around?If the gold flakes were at the bottom of the pan mix in with the oil that's copper and that's bearings period.

128

General Buick Tech / Re: Freshen up a motor

« on: August 13 2013, 08:26:01 PM »

Sorry to say gold flakes means bearings.

129

General Buick Tech / Re: unhooked wire

« on: August 11 2013, 11:34:50 AM »

o2 sensor .

130

For Sale/Trade/Want To Buy / Re: WTB 1 3/8 SWAY BAR

« on: February 22 2012, 06:23:24 PM »

I don't think that would fit on the front.

131

For Sale/Trade/Want To Buy / WTB 1 3/8 SWAY BAR

« on: February 22 2012, 09:44:17 AM »

Looking for 1 3/8 sway bar let me know what you have thanks.

132

IHADAV8 Playground / Re: New stuff for the car?

« on: February 15 2012, 10:34:33 AM »

thats to go faster and better ets, i know you what to beat on your car just like me.can't wait.

133

IHADAV8 Playground / New stuff for the car?

« on: February 15 2012, 08:46:24 AM »

So what did you do or bi for the car over the winter for this summer, and will you race it ?

134

IHADAV8 Playground / Re: Old TB's.com guys get in here now !!!

« on: February 14 2012, 04:56:49 PM »

I can tell you that in the Toronto section there a lot of people don,t like each other and no one says much there any more.

135

For Sale/Trade/Want To Buy / Block and Parts F/S

« on: January 27 2011, 01:29:42 PM »

http://www.turbobuicks.com/forums/parts-sale/96113-block-parts-f-s.html

I have a109 block done 30 over with one sleve all machine work was done at Rob Atchison Racing in London Ontario comes with 30 over pistons and stock rods,ARP head studs,front timing chain cover with all the hardware no crank. or cam $500.00
One set of used red MSD wires all number.$60.00
used coil and module good working order $150.00
TT 5.6 chip for 60lb injectors with alky boost set aat 25pounds $60.00
Turbo inlet bell polish $50.00
Exhaust housing AR .83 3 bolt $60.00
87 Crome Grille no chips or cracks $100.00

All parts are plus shipping.


**EDIT** Corrected link and copied info - SuperSix