Author Topic: Seat Belt Question  (Read 5601 times)

0 Members and 1 Guest are viewing this topic.

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5549
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Seat Belt Question
« on: August 05 2011, 12:18:44 PM »
On this 1994 Impala SS  I have, the drivers side front seat belt doesn't like rolling back up when released. Is there a way of cranking up the return pressure...or is the roll up mechanism fuked and I have to buy a new one?
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline SuperSix

  • Administrator
  • Turbo Street Outlaw
  • *******
  • Posts: 5071
  • PSI: 234
    • View Profile
Re: Seat Belt Question
« Reply #1 on: August 05 2011, 01:16:18 PM »
On this 1994 Impala SS  I have, the drivers side front seat belt doesn't like rolling back up when released. Is there a way of cranking up the return pressure...or is the roll up mechanism fuked and I have to buy a new one?

There may be a way to tweak it - but personally, I would NEVER mod anything to do with the seatbelt/restraint system.

you should be able to get a cheap replacement used off of eBay or an impala SS board.

I have a similar problem with the Eldorado - the driver's side shoulder portion doesn't retract. I got a replacement from the junkyard. The seat belt color is tan, not gray, but good enough for a driver.
'87 GN, 60lb, TA49, THDP, FTP cam, T+ lots o' shit - SOLD
'07 Ford F150 Lariat 2WD, 5.4L 3v - 255k
'20 Kubota BX2380. FEL, 60" deck
'78 IH/Case 184 Lo-Boy
'99 Kawasaki Bayou 400 4x4

Offline daveismissing

  • Two Buicks- too little money$$
  • Turbo Street Outlaw
  • *******
  • Posts: 6515
  • PSI: 3
  • Two Buicks- too little money$$
    • View Profile
Re: Seat Belt Question
« Reply #2 on: August 05 2011, 05:16:20 PM »
swap  the sides maybe kindledave
-Drain plug by Earl Brown, custom oil pan by Rich's Auto

Offline Charlief1

  • Just another kinky six
  • Turbo Street Eliminator
  • ******
  • Posts: 1348
  • PSI: 2
    • View Profile
Re: Seat Belt Question
« Reply #3 on: August 05 2011, 10:15:19 PM »
I had an 84 Camaro that had a simular issue. There was a recall on them because of this same issue. Take your VIN and call the dealer and see if there's a recall on it.
And remember, when dealing with children, silence may be golden but duct tape is silver.

Offline SuperSix

  • Administrator
  • Turbo Street Outlaw
  • *******
  • Posts: 5071
  • PSI: 234
    • View Profile
Re: Seat Belt Question
« Reply #4 on: August 06 2011, 01:13:52 AM »
Good point - They *might* repair it for free.
'87 GN, 60lb, TA49, THDP, FTP cam, T+ lots o' shit - SOLD
'07 Ford F150 Lariat 2WD, 5.4L 3v - 255k
'20 Kubota BX2380. FEL, 60" deck
'78 IH/Case 184 Lo-Boy
'99 Kawasaki Bayou 400 4x4

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5549
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Re: Seat Belt Question
« Reply #5 on: August 06 2011, 07:56:04 AM »
I had an 84 Camaro that had a simular issue. There was a recall on them because of this same issue. Take your VIN and call the dealer and see if there's a recall on it.

I'm friends with the partsman here in town at my friendly GM dealer. I'll hit him up on Monday and see what he says about a recall. Thanks for the tip.
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline SuperSix

  • Administrator
  • Turbo Street Outlaw
  • *******
  • Posts: 5071
  • PSI: 234
    • View Profile
Re: Seat Belt Question
« Reply #6 on: August 06 2011, 09:15:21 AM »
I had an 84 Camaro that had a simular issue. There was a recall on them because of this same issue. Take your VIN and call the dealer and see if there's a recall on it.

I'm friends with the partsman here in town at my friendly GM dealer. I'll hit him up on Monday and see what he says about a recall. Thanks for the tip.


Even without a recall - there's a much longer time they have to repair safety devices. Not sure how long - good to check though.
'87 GN, 60lb, TA49, THDP, FTP cam, T+ lots o' shit - SOLD
'07 Ford F150 Lariat 2WD, 5.4L 3v - 255k
'20 Kubota BX2380. FEL, 60" deck
'78 IH/Case 184 Lo-Boy
'99 Kawasaki Bayou 400 4x4

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5549
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Re: Seat Belt Question
« Reply #7 on: August 06 2011, 10:18:49 AM »
I'll be pounding on the Service Managers desk Monday morning. I drive them nuts up here making them go through the computer looking for Buick parts for me.
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline Pyro6

  • Turbo Street Eliminator
  • ******
  • Posts: 1327
  • PSI: 2
    • View Profile
Re: Seat Belt Question
« Reply #8 on: August 18 2011, 05:55:16 PM »
So how did you make out????

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5549
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Re: Seat Belt Question
« Reply #9 on: August 19 2011, 09:29:57 PM »
I smoked the clutch on the air con compressor on the Impala...so I've been trying to hunt down one of those. The new turbo showed up for the GN...so it's getting my attention this weekend. I'm gonna drop by the dealer Monday...and I'll let you know what they say.
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline TWIN86GNS

  • My car is almost ready!!!!
  • Turbo Street Limited
  • ***
  • Posts: 118
  • PSI: 0
    • View Profile
Re: Seat Belt Question
« Reply #10 on: August 27 2011, 11:43:13 PM »
Brad,

Well, what did they say???
Paul Beal
beal_paul@yahoo.ca

1986 GN  #1,  11.38 @ 120.25 mph  with a 1.501 60'
1986 GN  #2,  13.25 @ 102.95 mph with a 2.086 60'

 

SimplePortal 2.3.7 © 2008-2024, SimplePortal