Author Topic: Roses are red, violets are blue, my cars a hunk of turd and I wish it nothing but pain  (Read 12539 times)

0 Members and 1 Guest are viewing this topic.

Offline Top Speed

  • Don't Tread on Me
  • Turbo Street Outlaw
  • *******
  • Posts: 2548
  • PSI: -2
    • View Profile
Never heard of a water pump that wouldn't pump....usuall y they leak and then get replaced.  If in doubt you could take it off and look at the impeller to see if it is intact.
Champion Irons w/T&D roller rockers, TA-61 turbo, 206/206 Comp Cam,  57 lb/hr Siemens Injectors, 3000 stall PTC, PTE Plenum w/RJC Power Plate, 70 mm Accufab Throttle Body, RJC 325 Megacooler, TurboTweak 5.7/ Alky Control w/M1 methanol, 23 psig on the street, Puddn' Power engine, Borla Exhaust

Chris

Offline SuperSix

  • Administrator
  • Turbo Street Outlaw
  • *******
  • Posts: 5071
  • PSI: 234
    • View Profile
IOt can happen. The impeller can become loose, and as the load on it increaes, the flow reduces.

There's really not much more it can be. Do the radiator cores looked clogged? Do you ahve a hose collapsing?

Flow Cooler makes a NICE unit
http://store.summitracing.com/egnsearch.asp?N=4294924500+4294908256+4294838996+4294925022+4294840137+115+300293&autoview=sku

$81.99 though  :confused;
'87 GN, 60lb, TA49, THDP, FTP cam, T+ lots o' shit - SOLD
'07 Ford F150 Lariat 2WD, 5.4L 3v - 255k
'20 Kubota BX2380. FEL, 60" deck
'78 IH/Case 184 Lo-Boy
'99 Kawasaki Bayou 400 4x4

DCEPTCN

  • Guest
Radiator has only a couple of hundred miles on it.

Offline Recklessrob

  • Turbo Street Outlaw
  • *******
  • Posts: 5112
  • PSI: 3
    • View Profile
The impeller could be clogged up or rotted out. When are the fans coming in ?

As for water pumps, Poston's sells the high flow pump for about $40. I have
one in my Mazda, and it's da bomb !
Rob

Offline Dragonational

  • Turbo Street Stock
  • ****
  • Posts: 288
  • PSI: 0
    • View Profile
D i am having the same problem with the new motor in my car.  Only difference is mine likes to pin the needle on 250 :mad; .  I am going to check the basics soon but if you have checked the therm and the rad then what else is there short of checking the water pump or pulling all of your hoses to see if there is any blockage in the lines? Not sure but when you find it let us know....and then come fix mine :D
i like burnouts they smell good

Offline 87natty

  • Turbo Street Outlaw
  • *******
  • Posts: 3616
  • PSI: 0
    • View Profile
    • http://www.wix.com/lynch455/science
I've had good luck with the Autozone $20 special. Use a Fel=Pro gasket.
My 1958 Mamiya can beat up whatever camera you just wasted your money on.

Offline Recklessrob

  • Turbo Street Outlaw
  • *******
  • Posts: 5112
  • PSI: 3
    • View Profile
When I got the New HP pump I compared them, and the impellers are totally different. The HP pump has a nice contoured cast aluminum impeller instead
of the stamped steel with bent fins.
Rob

Offline 87natty

  • Turbo Street Outlaw
  • *******
  • Posts: 3616
  • PSI: 0
    • View Profile
    • http://www.wix.com/lynch455/science
Mine was a GMP, cast fins.
My 1958 Mamiya can beat up whatever camera you just wasted your money on.

Offline Recklessrob

  • Turbo Street Outlaw
  • *******
  • Posts: 5112
  • PSI: 3
    • View Profile
The bearings are supposed to be different too, but I couldn't tell without cutting it open.
Rob

 

SimplePortal 2.3.7 © 2008-2024, SimplePortal