Author Topic: Moser Axles-When?  (Read 6396 times)

0 Members and 1 Guest are viewing this topic.

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5549
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Moser Axles-When?
« on: October 13 2013, 05:57:45 PM »
At what short time is it good to go with Moser axles? I normally pull low 1.6's...is it time?
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9882
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Moser Axles-When?
« Reply #1 on: October 13 2013, 07:42:20 PM »
I think so
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9882
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Moser Axles-When?
« Reply #2 on: October 13 2013, 07:50:42 PM »
be nice if you could hold out until you need a new posi...then you could upgrade to 30 splines with a matching posi
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline Forzfed

  • Turbo Street Eliminator
  • ******
  • Posts: 1337
  • PSI: 5
  • Boost n00b
    • View Profile
Re: Moser Axles-When?
« Reply #3 on: October 13 2013, 08:02:56 PM »
Do you have a girdle?  What does your car weigh?  My car weighs in at 4050lb with me in it.  I pulled a 1.61 60ft three times then snapped the axle on the next pass and this was still with the stock converter, unopen motor with only a TE-44.  I upgraded to 30 spline, but if I were you play it safe and get some better axles.

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5549
  • PSI: 3
  • YOU CAN'T HANDLE THE TRUTH!!!!
    • View Profile
Re: Moser Axles-When?
« Reply #4 on: October 13 2013, 08:21:06 PM »
Do you have a girdle?  What does your car weigh?  My car weighs in at 4050lb with me in it.  I pulled a 1.61 60ft three times then snapped the axle on the next pass and this was still with the stock converter, unopen motor with only a TE-44.  I upgraded to 30 spline, but if I were you play it safe and get some better axles.

Moser girdle...Aubur n Pro Series Posi. Never weighed the car...but it's a T Top power everything with the following weight reduction: Air con delete,,,but retains the heater box...RJC lower race pulley...9.5" NL convertor...al uminum driveshaft...a luminum rear drums...sound deadener removed...LT1 starter...F Body rad conversion...a luminum front and rear bumper inners...and the driver weighs 170...the oil cooler lines and adaptor were tossed in Lake Ontario...the IC fan is used as a Frisbee at the shop...someone please do the math.
« Last Edit: October 13 2013, 08:27:39 PM by Scoobum »
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline TexasT

  • Legend in my own mind
  • Turbo Street Outlaw
  • *******
  • Posts: 2170
  • PSI: 1
  • So, This black car is fast?
    • View Profile
Re: Moser Axles-When?
« Reply #5 on: October 13 2013, 09:56:51 PM »
Are you good at body work? Have you seen what a broke axle does to a quarter panel as it exits the housing?

Put em in. Just not worth the hassle of breaking one to find their limits.
Rich

"Goals without actions are just dreams."

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9882
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Moser Axles-When?
« Reply #6 on: October 13 2013, 11:52:07 PM »
Are you good at body work? Have you seen what a broke axle does to a quarter panel as it exits the housing?

Put em in. Just not worth the hassle of breaking one to find their limits.

That does not happen when you weld ford axle tube ends on the housing
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline motorhead

  • Turbo Street Outlaw
  • *******
  • Posts: 2265
  • PSI: 4
  • look at my balls... look at them!!!
    • View Profile
Re: Moser Axles-When?
« Reply #7 on: October 14 2013, 09:37:41 AM »
Are you good at body work? Have you seen what a broke axle does to a quarter panel as it exits the housing?

Put em in. Just not worth the hassle of breaking one to find their limits.

That does not happen when you weld ford axle tube ends on the housing

Or when you convert to disk brakes...
>>>Das Instagram<<<
'80 LeMans Wagon|'87 Monte Carlo SS|'92 Camaro Z28|'07 TrailBlazer SS|'15 Colorado Z71|'19 Hellcat Widebooty M6

Offline bescurred

  • Bone Stock
  • **
  • Posts: 42
  • PSI: 0
  • Boost n00b
    • View Profile
Re: Moser Axles-When?
« Reply #8 on: October 18 2013, 05:05:11 PM »
Do you have a girdle?  What does your car weigh?  My car weighs in at 4050lb with me in it.  I pulled a 1.61 60ft three times then snapped the axle on the next pass and this was still with the stock converter, unopen motor with only a TE-44.  I upgraded to 30 spline, but if I were you play it safe and get some better axles.


You have a TR that weighs 4050 with you in it?

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9882
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Moser Axles-When?
« Reply #9 on: October 19 2013, 10:01:49 AM »
Do you have a girdle?  What does your car weigh?  My car weighs in at 4050lb with me in it.  I pulled a 1.61 60ft three times then snapped the axle on the next pass and this was still with the stock converter, unopen motor with only a TE-44.  I upgraded to 30 spline, but if I were you play it safe and get some better axles.


You have a TR that weighs 4050 with you in it?

That is not all that unusual.
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline bescurred

  • Bone Stock
  • **
  • Posts: 42
  • PSI: 0
  • Boost n00b
    • View Profile
Re: Moser Axles-When?
« Reply #10 on: October 19 2013, 02:27:52 PM »
Do you have a girdle?  What does your car weigh?  My car weighs in at 4050lb with me in it.  I pulled a 1.61 60ft three times then snapped the axle on the next pass and this was still with the stock converter, unopen motor with only a TE-44.  I upgraded to 30 spline, but if I were you play it safe and get some better axles.


You have a TR that weighs 4050 with you in it?

That is not all that unusual.




Hmmmm I weighed my full weight 86 hardtop GN with me in it was 3650ish...that's crazy that there could be 400 pounds difference!

Offline Forzfed

  • Turbo Street Eliminator
  • ******
  • Posts: 1337
  • PSI: 5
  • Boost n00b
    • View Profile
Re: Moser Axles-When?
« Reply #11 on: October 19 2013, 06:56:34 PM »
Do you have a girdle?  What does your car weigh?  My car weighs in at 4050lb with me in it.  I pulled a 1.61 60ft three times then snapped the axle on the next pass and this was still with the stock converter, unopen motor with only a TE-44.  I upgraded to 30 spline, but if I were you play it safe and get some better axles.


You have a TR that weighs 4050 with you in it?

The reason it weighs so much is because of all the extras I have in it.  I told my buddy who own's a Stage II car, how much it weighed and he said, "No way!"  Then I opened my trunk for him and he then said,  "Yeah, possibly."  Car weighed 3800lbs when I put it on the scale.  I have T-Tops, the concert sound system with 10 after market speakers, 4 subs, 5 amps, and an electronic crossover, 10 disc exchanger.  Car also has carpeted trunk kit.  And when I race I couldn't be bothered with removing anything, not even the spare.

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9882
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Moser Axles-When?
« Reply #12 on: October 19 2013, 08:12:55 PM »
those damn cross overs do it every time
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline daveismissing

  • Two Buicks- too little money$$
  • Turbo Street Outlaw
  • *******
  • Posts: 6515
  • PSI: 3
  • Two Buicks- too little money$$
    • View Profile
Re: Moser Axles-When?
« Reply #13 on: October 19 2013, 08:32:55 PM »
fuzzy dice?
-Drain plug by Earl Brown, custom oil pan by Rich's Auto

Offline Forzfed

  • Turbo Street Eliminator
  • ******
  • Posts: 1337
  • PSI: 5
  • Boost n00b
    • View Profile
Re: Moser Axles-When?
« Reply #14 on: October 20 2013, 03:25:01 AM »
fuzzy dice?

No, they don't weigh enough.  I have solid gold dice with diamonds. :rock:

 

SimplePortal 2.3.7 © 2008-2024, SimplePortal