IHADAV8.com - Turbo Buick Tech, and Nonsense
General => IHADAV8 Playground => Topic started by: Recklessrob on January 20 2006, 01:01:08 AM
-
Hopefully he has some good kill stories to tell
from modding his car when he returns. :psix;
-
I was about to worry about his old ass too...
-
Maybe he finally found a girlfriend? He'll be back with stories like Lepizzle. Zipper, balls, passed out, my forehead, hungover. We'll have to phill in the blanks. :rofl;
-
We'll have to phill in the blanks. :rofl;
You deserve a medal for that one!
-
Aww damn, I was about to hijack this thread....I'll start a new one and edit this post with a link.
http://ihadav8.com/phpBB2/viewtopic.php?p=5079#5079
-
I fckng wish that any and all of that were true. But no such luck in my case. I would be loping my mule if I could find it. Just planning out my next mod. Had Lou do the Thunderfat i/c last Sat. Required a little more fitting than I expected. It came shipped with a 1" crack running in the weld bead on the passenger side upper i/c shroud. Welding it back up would not have been worth the effort and made it uglier. It is only maybe .025 wide at the widest point and 1" long, and doesn't really show unless you know about it, but it is just the idea that people sell/ship defective products like this. The shipping container was ibn too good of condition for it to be shipping related, so it was supplied and shipped that way. Also the seller, who I believe sponsors this site, or at least advertises on it, forgot the passenger side mounting bracket, but I got it within a week of getting the i/c itself. Always buy direct from the manufacturer whenever possible, unless there is a very good reason not to. Also, the lower i/c shroud was misaligned compared to the end of the upper i/c shroud by about 3/8" or so, and about 1/4" had to be trimmed off of the lowest portion of the upper i/c shroud to get it to clear the sway bar, and leave some room for engine movement. Doesn't line up at the top end real well either. the i/c tube ends are too close together, so it will not line up perfectly with both the turbo outlet and the up pipe inlet. You can use about 3/8" washer on the driver side and that will line up the passenger side turbo outlet to i/c inlet, but then it will show on the alignment of the up pipe not running straight in line with the longitutidal axis of the motor itself. Lou lined mine up pretty well, and then I did a little more alignmednt work on it, and it looks ok, but it should look better for the money that thiose sell for. It also weighs about 2X-3X as much as the stocker.
-
Gary here is your next mod!
http://www.turbobuicks.com/forums/showthread.php?t=45761
-
I'm sure Gary needed a nap after the above post.....
-
I'm sure Gary needed a nap after the above post.....
My dial up connection is still downlodaing that post!
-
Sorry, i did want to catch everybody up to date, to alert everybody about insisting on pictures from some vendors, supporting the manufacturer direct whenever possible, and choosing a product and supplier very carefully, and sometimes paying the most, is worth it. Sorry for the long post, and no, I did not take a nap, I had just gotten up this am, played hookey today.
-
Gary here is your next mod!
http://www.turbobuicks.com/forums/showthread.php?t=45761
---------------------------------------------------
Chris: If I do that, then I will need a Translator Plus also, right.
If I do this, what benefits will my car see. My car seems to be running very good and smooth currently, so if the only benefit of the LS1 MAf & Translator Plus is smoothness and ability of tuning, then ???
-
Well you will need a translator at least. I actally make my timing adjustments in the chip so I didn't need the trans+.
You know if you are not having MAF problems there is no reason to upgrade.
I just wanted to do it!
-
Not having MAF problems, but it would be convenient timing to do it when I do the Mark Hueffman cold air kit, so i do not have to change tubing sizes but 1 time. What is the best, the LS1, and is that a 3" or a 4", and can I get a corresponding size of tubing from BuickGN.
-
The LS1 is 3.5". I upgraded mine when I went to the Big Mouth kit. Mark Hueffman has the 3.5" MAF pipe to fit the LS1 MAF perfectly.
-
Why Thunderfab?
-
Because Thunderfab had one of the best reputations out there for fit, function, & cost. Their function is great, fit sucks, & they are now $ 700 retail where they were about $600 just about a year ago. They also look somewhere close to stock. If I was to do this over again, it would be the PT&E factory mount which also has increased in price and now is about $840 through the least expensive source that I know of,(Full Throttle Speed & Style), plus shipping. It is the best factory mount out there currently. I think that Thunderfab was considered the best out there available in it's price range. Good to hear from you again Gordy, hope that you and family are in good health and spirits.
-
Welcome back Gary. Lose the stock air filter and components. They
even hinder a stock car, not to mention killing yours.
-
Thanks, Rob. I really wasn't gopne anywhere, I was keeping an eye on you guys incognito, so to speak, I guess. Air filter set-up is the next item to go, just can't make up my mind which one. So far in the lead is the Mark Hueffman big mouth, just can't decide whether I want to go with the translator plus & ls1 now, or wait till later and maybe have to do hose-fitting size changes due to the changeover. Probably should wait for the maf to go, but I ahve very good luck with them, this being my fifth turbo Buick, and never had to replace one yet. The big mouth, translator plus & lsi maf sounds like about $580-$610, and I don't know if I want to shell that much on a fckng air intake system right now. What's the 1st class hot set-up currently for upper & lower rear control arms?????
-
I like the Hotchkis ones I'm running now. Many like
the ones from Metco. I'd stay away from South Sides on a street car.
Ededbrocks are very similar to Hotchkis, but I can't say if there are any exhaust
clearance issues with their braces or not.
-
I have HrPartsnstuff but I dont know the difference between any of them.
-
Anything is better than stock. I prefer non adjustable, as your performance depends on who installs it. I guess you could get the thrust angle set at a good alignment shop.
-
I have the Metco uppers and lowers. They're adjustable but they come from the factory with the stock-factory preset. They also come with the c-clamps or whatever they're called if you ever need them. A world of difference over the stock ones.
-
Most, or a lot of the upper & lower rear control arms available out there are polyurethane, or do not list what they use for a buffering material and that is my concern. Also, Global Wests claim on their spherical bushing rear upper or lower adjustable is that it allows full articulation, where almost all of the others do not. On the other hand, Global West only makes the adjustable one that I described and a solid one, but do not make an upper and a lower also. Makes me worry when a company only makes one of a supposedly set of something. Edelbrock has something similiar to that design, but not available for our cars. Currie makes something new called a "Johnny joint" very similiar in concept.
-
If you want the car to handle you will need the spherical bearings where the arms attach to the frame. This will take some of the bind out. If the car is just for street duty with occasional spirited driving then it would not matter too much and you just get standard bushings.
-
You mean Heim joints? On all points?
-
A Heim Joint's technicial name is spherical bearing, I believe, and yes. without at least one end, I forget which one, of the upper or lower rear control arm being spherical, it's onlymovement is up or down. A spherical (heim joint) bearing allows a certain amount of atriculation sideways, and full movement up & down. Unless you are running a bar to keep the body centered on the chassis, such as the GNX one, it is claimed that the car will move sideways enough to cause the binding of the bushings, which also causes squeaking. Global West, has one end of the adjustable control arm with a Heim joint. Most like it, a few don't.
-
I have not seen anyone make control arms with Heim/Spherical connection at both ends.
Everything you stated Gary is correct.
-
I have not seen anyone make control arms with Heim/Spherical connection at both ends.
Everything you stated Gary is correct.
-
So, Racer X, you're a martini drinker & racer, what is your advice in regards to what should I run in the way of a upper & lower rear control arms. I am confused, not about the choices, but which one is the best for my application. I like spirited freeway romps, spirited freeway on & off ramps, will probably only see a stoplight race or two, Global West adjustable upper control arm with the frame end Heim joint, Spherical Bearing) and whose solid lower control arms. I dunno, and maybe a bigger Full throttle Speed & Style rear sway bar? I am crowded at the front end and I am going to leave the front sway bar factory dia. Does that sound good to ya?
-
So, Racer X, you're a martini drinker & racer....
BUSTED! :bigeyes;
I don't see a need to go with adjustables unless you have the need to change the pinion angle.
I can not reccomend a specific manufaturer over another since I have not tried them all and that would not be fair.
So, here's what I can say, you are correct in the the hiem joint at the frame will allow the 4 link to articulate more than it does now, but will not eliminate the problem. Since the two arms are of different length and angle they will be swinging at a diiferent arc which will cause the bind sooner or later. The only way to rid ourselves of this is to go with a 3 link, but no need for that on the street.
IF you are going to hot rod the car around corners what will happen with the stock set up is that the rear will roll to the point that it can no longer roll due to the bind. When this happens it will be similar to coil bind where your spring rate goes to infinity. The car will roll and the finally the rear will just snap around on you. With the heim joints you will get more roll befor ethis happens, thus a more effective roll rate which will be more predictable throught the corner.
I am a big advocate for leaving the stock front bar. I see a lot of people going to a bigger front bar. Why? I don't know. Our cars have an inherent push/understeer to them from the factory. To increase the push in a car you INCREASE the size of the front bar. To lessen the effects of understeer you INCREASE the size of the REAR bar. So leave the front bar alone.
When you are tuning a chassis, you want to do ONE thing at a time. If you make wholesale changes to the chassis and something doesn't feel right you won't know if it was the springs, bars, shocks, etc... that had the detrimental effect on the handling.
As for sway bars, when you increase the diameter of a bar by just an 1/8 of an inch it increases the effectiveness to the power of 4 over the previous diameter. I have an excel spreadsheet that I use when doing all of this that has all of the formulas in it. I will try to upload it to my website in the next few days.
So, what do I think? I think that if Mama Cass had given that sandwich to Karen Carpenter they both would still be alive today! For what you are looking for Gary, you don't need to spend a ton of dough on shocks and springs and bars. Put all the braces on the car and a set of Bilstiens and you will fine for the freeways and off ramps. :D
Racer (typed all that hunt and peck style) X :rolleyes:
-
I'm glad you wrote that last paragraph... 'cause thats what I was going to say!
-
Before who wrote that last paragraph, you mean Racer X?
-
yes.... I mean racer X
-
Heres a pic of my car with the Hotchkis suspension.
I couldn't get all of it in laying on the floor.
(http://img92.imageshack.us/img92/6721/suspensionexhview6sc.th.jpg) (http://img92.imageshack.us/my.php?image=suspensionexhview6sc.jpg)
-
Thanks for posting that pic, Rob. Nice looking set-up. I think that I am going to go with the Global west lower rear control arm with the spherical bearing on the frame side, and the Del-A-Lum bushing on the opposite end, and Full Throttle Speed & Style 1 3/8" rear sway bar, and I haven't decided on a brand of upper rear control arm yet, and maybe air bags in the springs. Global West has a rear sway bar, but it is only a 1". I am not sure what the original factory stock dia of the rear sway bar is, looks like 7/8" or 1", just looked, didn't measure it.
-
The factory bar is 7/8". Did I read that right? You are going with a 1-3/8" rear bar? That'll get rid of the understeer alright!
From what I am seeing it looks as if you are going for the straight line set up instead of the turning and burning set up.
-
I spun out last night and blew a tire...
-
I spun out last night and blew a tire...
Because you've posted, I'm assuming you're OK. How is the car ?
-
Alright. I goosed in around a sharp on ramp and she downshifted, the rear end whipped out from behind me. So I bounced off a curb and spun into the off ramp, across a median like in Bullitt when the Charger hit the gas station and the Mustang skidded into a ditch.
The car didn't stall so I casually went the other direction and limped it to a side street. Scraped a rim pretty bad, but everything else was OK. The worst part was putting on the spare and realizing that was flat too...
My buddy saw it, and instead of being pissed, we talked about how I should do it next time. Fear no turn! :smt071
-
I whipped my S-10 out sideways tonight. I forgot how
much fun a stick is ! :supz:
-
The factory bar is 7/8". Did I read that right? You are going with a 1-3/8" rear bar? That'll get rid of the understeer alright!
From what I am seeing it looks as if you are going for the straight line set up instead of the turning and burning set up.
---------------------------------------------------------
Greg: Ireally didn't measure, I just looked down under the car, and it appears to be 7/8", or it could be an 1", I will measure it this weekend. I am actually trying for a compromise between the two. I have heard a lot of favorable comments that the bar is very similiar to the no longer available ATR bar. As I am not changing the stock front swaybar, I feel ok going a little thick on the rear, hoping that does get rid of some or most of the undesirable understeer, and help the car stay flat in the cormers. We'll see. I will have to do some more studying before I buy anything.