Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Norm340

Pages: [1]
2
General Buick Tech / U Joint Question
« on: November 06 2021, 12:07:55 PM »
I know, I should have asked this question before I ordered these but....

Would these U joints from Rock Auto be the correct ones for a 87 GN?

Thanks
Norm

ACDELCO 45U0110 {#89029292} (Heavy Duty) Greaseable Super Strength Info
Fits At Transmission; Inside Lock Rings
or at Rear Axle; Inside Lock Rings

https://www.rockauto.com/en/catalog/buick,1987,regal,3.8l+231cid+v6+turbocharged,1020957,drivetrain,universal+joint,2392


3
General Buick Tech / ICM Question
« on: February 07 2021, 11:05:20 AM »
Was looking on Rock Auto for an Ign Control Module for the 87 GN and was wondering...
What is a Magnavox unit?
Thanks

GM GENUINE D1996 {#19260720, 24503624} Info
FitsW/MAGNAVOX UNIT; WITH MAGNAVOX UNIT
orwith Magnavox Type I Ignition System


4
IHADAV8 Playground / The Day a V6 ran in Pro Stock
« on: September 24 2020, 12:16:29 PM »
https://youtu.be/nkxr0CPiZGY?t=80

Love the comment from the announcer in the final
Its 268 Cubic inches against a refrigerator under the hood of Glidden's Car...LOL   

5
General Buick Tech / Rear Control Arms
« on: September 14 2020, 07:50:31 PM »
Hey Guys

If I was going to remove the lower control arm to replace the bushings.
Is there a certain way to remove the lower arms?
Like having jack stands under the frame and the floor jack under the diff then loosen the bolts.
Maybe only remove one arm at a time, is there tension on the sway bar?
That kind of stuff.

Kinda know how to remove and install the bushings but the arms not so much.

Thanks

6
For Sale/Trade/Want To Buy / WTB - Hood Pad
« on: September 21 2019, 12:51:36 PM »
Hey Guys


I'm in need of a hood pad for my 87 GN.
Anyone have one for sale or have any ideas, would really like one with the wording on it.




Thanks

7
A/C, Heating and Cooling / Heater box sealing
« on: June 16 2019, 03:39:17 PM »
I'm looking for what would be best to use to seal the outside top of the heater/AC box at the firewall.
OEM looked like a thick tar that has harden over the years.
Kinda thought of maybe using a black seam sealer and or Windshield sealant or something similar?
Any ideas would be appreciated.


Thanks   

8
General Buick Tech / SM readings
« on: June 18 2018, 03:41:45 PM »
Hello

New GN owner here.
Hook up a Scanmaster today and was wondering what you guys thought about the readings.
With the exception of a new Densco O2 sensor and 2 breathers for the valve covers, and some NGK spark plugs I noticed.
Its a very original 87 GN with 57k Miles or 94k Kms for us Canadians.

In park idling in the garage after a short drive.
Closed loop
O2V 302-785
MAF 5
LV8 37-39
Volts 13.3 13.4
INT 122-129
BLM 131
Coolant 182
Air Temp 96
RPM 775
TPS .40
IAC 11-13
O2CC 120

Thanks
Norm

Pages: [1]
SimplePortal 2.3.7 © 2008-2024, SimplePortal